Henny Penny Repair in Matthews, NC
Matthews businesses call us for fast, honest Henny Penny repair.
- Licensed & insuredCommercial refrigeration and kitchen equipment technicians
- $135 service callClear price before any work starts
- $50 off your repairWhen you book online or mention the website
- Warranty on every job30-day labor, 90-day parts, extended 1, 3 or 5 years on select work
- Open 7 days a weekMon–Sat 8 AM–6 PM · Sun 10 AM–3 PM
- Same-day serviceWhen you call early — trucks stocked with common parts
You get a flat $135 service call and a written price before any work starts. Henny Penny makes pressure fryers, open fryers and holding cabinets, and we repair them on-site.
Henny Penny service for Matthews businesses
Matthews combines a walkable downtown restaurant row with heavy retail along US-74 and a busy medical corridor. We serve businesses near downtown Matthews on Trade Street, Independence Boulevard (US-74) and Sycamore Commons, including ZIP codes 28104, 28105 in Mecklenburg County, NC.
Our technicians are in Matthews most days of the week, so a call from a business on Sycamore Commons usually fits into the same day's route. Summer heat in the Charlotte region pushes condensers and compressors to their limit; for Matthews kitchens we check airflow, coil condition and electrical parts on every visit. From quick-service counters near Sycamore Commons to full kitchens near downtown Matthews on Trade Street, Matthews businesses rely on us for Henny Penny work. Mecklenburg County health inspectors check cold-holding at 41°F or below and hot-holding at 135°F or above — we repair your Henny Penny to hold those numbers.
Henny Penny problems we fix in Matthews
- Henny Penny commercial fryer: oil overheating or not reaching set point
- Henny Penny commercial fryer: fryer won't light or heat
Henny Penny equipment we repair
Save $50 on your repair
Book online or mention our website when you call and we take $50 off the repair. The service call is a flat $135, and you get a clear price before any work begins — no surprises.
Typical jobs we handle
Examples of common repairs on commercial refrigeration and kitchen equipment.
- Commercial FryerConvenience Stores & Gas Stations
Fryer overheating and tripping the high-limit
- What we found
- Temperature probe failing
- What we did
- Replaced the probe and calibrated the controller
✓ Typically fixed in one visit
- Commercial FryerRestaurants
Fryer won't heat before lunch
- What we found
- Weak thermopile
- What we did
- Replaced the thermopile and tested the gas valve
✓ Typically fixed in one visit
- Commercial Range & CooktopRestaurants
Range pilots keep going out
- What we found
- Worn thermocouples on two burners
- What we did
- Replaced thermocouples, cleaned pilot assemblies
✓ Typically fixed in one visit
- Walk-In FreezerSchools & Universities
Ice building up on the freezer floor near the door
- What we found
- Torn door gasket and failed door-frame heater
- What we did
- Replaced the gasket and frame heater wire
✓ Typically fixed in one visit
- Undercounter & Worktop RefrigeratorRestaurants
Chef base losing temperature during the rush
- What we found
- Front grille and condenser clogged with grease
- What we did
- Cleaned the condenser, replaced a worn drawer gasket
✓ Typically fixed in one visit
- Walk-In CoolerGrocery Stores & Supermarkets
Walk-in cooler slowly warming over several days
- What we found
- Condenser coil packed with dust and cottonwood; high head pressure
- What we did
- Deep-cleaned the condenser, checked charge and amperage
✓ Typically fixed in one visit
- Griddle & CharbroilerFood Trucks
Griddle has a cold spot on one side
- What we found
- Clogged burner ports
- What we did
- Cleaned and adjusted the burner, checked the thermostat
✓ Typically fixed in one visit
- Ice MachineHospitals & Senior Living
Nugget ice machine leaking onto the floor
- What we found
- Cracked drain hose behind the unit
- What we did
- Replaced the hose, cleaned and sanitized the machine
✓ Typically fixed in one visit
Examples for illustration. Every job is diagnosed on site; parts, time and price depend on the equipment.
Our warranty
Labor warranty on every repair.
Parts warranty on every part we install.
Extended warranty available on select repairs and installations. The exact term is written on your estimate before work starts.
Frequently asked questions
Do you repair Henny Penny equipment in Matthews?
Yes. We repair Henny Penny commercial fryer for businesses throughout Matthews, NC.
Are you an authorized Henny Penny dealer?
No — we are an independent commercial service company. We repair Henny Penny equipment and warranty our work for 30 days labor and 90 days parts.
How much does Henny Penny repair cost in Matthews, NC?
The service call is a flat $135, which covers the trip and diagnosis. After diagnosis you get a written price for the repair before any work starts, and you save $50 on the repair when you book online or mention our website.
What are your hours in Matthews?
We are open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). Call (980) 983-2911 or send a request online and the first available operator will call you back.
Hours & contact
Commercial Appliances is open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). We serve Matthews, NC.
Phone: (980) 983-2911
Email: omnicommercialrefrigeration@gmail.com
Based in Charlotte, NC. We are a mobile service company — our technicians come to your business.
| Monday | 8:00 AM – 6:00 PM |
|---|---|
| Tuesday | 8:00 AM – 6:00 PM |
| Wednesday | 8:00 AM – 6:00 PM |
| Thursday | 8:00 AM – 6:00 PM |
| Friday | 8:00 AM – 6:00 PM |
| Saturday | 8:00 AM – 6:00 PM |
| Sunday | 10:00 AM – 3:00 PM |