Hobart Repair in Monroe, NC
Need Hobart repair in Monroe, NC? We send commercial technicians to restaurants, bars, stores and institutional kitchens across Monroe every week.
- Licensed & insuredCommercial refrigeration and kitchen equipment technicians
- $135 service callClear price before any work starts
- $50 off your repairWhen you book online or mention the website
- Warranty on every job30-day labor, 90-day parts, extended 1, 3 or 5 years on select work
- Open 7 days a weekMon–Sat 8 AM–6 PM · Sun 10 AM–3 PM
- Same-day serviceWhen you call early — trucks stocked with common parts
Hobart makes dishwashers, mixers and slicers, and we repair them on-site.
Hobart service for Monroe businesses
Monroe is the Union County seat, with food manufacturing, a hospital, schools and a long restaurant and grocery corridor along US-74. We serve businesses near downtown Monroe on Main Street, Roosevelt Boulevard (US-74) and the Charlotte–Monroe Executive Airport area, including ZIP codes 28110, 28112 in Union County, NC.
Union County health inspectors check cold-holding at 41°F or below and hot-holding at 135°F or above — we repair your Hobart to hold those numbers. When a part is not on the truck, we order it the same day from Charlotte-area suppliers and come back to Roosevelt Boulevard (US-74) as soon as it arrives. Our technicians are in Monroe most days of the week, so a call from a business on the Charlotte–Monroe Executive Airport area usually fits into the same day's route. Because we also work in Indian Trail and Wesley Chapel, a technician is often already nearby when a Monroe business calls.
Hobart problems we fix in Monroe
- Hobart commercial dishwasher: machine not filling or not draining
- Hobart commercial dishwasher: dishes not coming out clean
- Hobart mixer, slicer and food prep: slicer blade dull or wobbly
- Hobart mixer, slicer and food prep: safety interlock fault
Hobart equipment we repair
Save $50 on your repair
Book online or mention our website when you call and we take $50 off the repair. The service call is a flat $135, and you get a clear price before any work begins — no surprises.
Typical jobs we handle
Examples of common repairs on commercial refrigeration and kitchen equipment.
- Mixer, Slicer & Food PrepBakeries
Planetary mixer grinding in second speed
- What we found
- Worn transmission gear
- What we did
- Replaced the gear and lubricated the gearbox
✓ Usually needs a part ordered — two visits
- Commercial DishwasherRestaurants
Dishwasher not draining
- What we found
- Drain valve stuck with debris
- What we did
- Cleared and rebuilt the drain valve
✓ Typically fixed in one visit
- Commercial DishwasherHotels & Banquet Facilities
Dish machine final rinse at 160°F
- What we found
- Booster heater element burned out
- What we did
- Replaced the element, verified 180°F final rinse
✓ Typically fixed in one visit
- Refrigerated Display CaseGrocery Stores & Supermarkets
Glass-door merchandiser fogging up
- What we found
- Door anti-sweat heater failed
- What we did
- Replaced the door heater and checked the controller
✓ Typically fixed in one visit
- Soft Serve & Frozen Drink MachineIce Cream & Frozen Yogurt Shops
Soft serve coming out runny
- What we found
- Dirty condenser and worn drive belt
- What we did
- Cleaned the condenser, replaced the belt, adjusted viscosity
✓ Typically fixed in one visit
- Ice MachineConvenience Stores & Gas Stations
Ice machine showing a flashing error light
- What we found
- Water inlet valve not opening
- What we did
- Replaced the inlet valve and verified full fill
✓ Typically fixed in one visit
- Walk-In CoolerRestaurants
Walk-in cooler at 48°F before dinner service
- What we found
- Evaporator fan motor seized; coil starting to ice
- What we did
- Replaced the fan motor, cleared the coil, verified 36°F box temperature
✓ Typically fixed in one visit
- Undercounter & Worktop RefrigeratorRestaurants
Chef base losing temperature during the rush
- What we found
- Front grille and condenser clogged with grease
- What we did
- Cleaned the condenser, replaced a worn drawer gasket
✓ Typically fixed in one visit
Examples for illustration. Every job is diagnosed on site; parts, time and price depend on the equipment.
Our warranty
Labor warranty on every repair.
Parts warranty on every part we install.
Extended warranty available on select repairs and installations. The exact term is written on your estimate before work starts.
Frequently asked questions
Do you repair Hobart equipment in Monroe?
Yes. We repair Hobart commercial dishwasher, mixer, slicer and food prep for businesses throughout Monroe, NC.
Are you an authorized Hobart dealer?
No — we are an independent commercial service company. We repair Hobart equipment and warranty our work for 30 days labor and 90 days parts.
How much does Hobart repair cost in Monroe, NC?
The service call is a flat $135, which covers the trip and diagnosis. After diagnosis you get a written price for the repair before any work starts, and you save $50 on the repair when you book online or mention our website.
What are your hours in Monroe?
We are open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). Call (980) 983-2911 or send a request online and the first available operator will call you back.
Hours & contact
Commercial Appliances is open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). We serve Monroe, NC.
Phone: (980) 983-2911
Email: omnicommercialrefrigeration@gmail.com
Based in Charlotte, NC. We are a mobile service company — our technicians come to your business.
| Monday | 8:00 AM – 6:00 PM |
|---|---|
| Tuesday | 8:00 AM – 6:00 PM |
| Wednesday | 8:00 AM – 6:00 PM |
| Thursday | 8:00 AM – 6:00 PM |
| Friday | 8:00 AM – 6:00 PM |
| Saturday | 8:00 AM – 6:00 PM |
| Sunday | 10:00 AM – 3:00 PM |