Mixer, Slicer & Food Prep Repair in Mint Hill, NC
When a mixer, slicer and food prep goes down in Mint Hill, food, sales and inspections are on the line.
- Licensed & insuredCommercial refrigeration and kitchen equipment technicians
- $135 service callClear price before any work starts
- $50 off your repairWhen you book online or mention the website
- Warranty on every job30-day labor, 90-day parts, extended 1, 3 or 5 years on select work
- Open 7 days a weekMon–Sat 8 AM–6 PM · Sun 10 AM–3 PM
- Same-day serviceWhen you call early — trucks stocked with common parts
Our technicians arrive with common parts and fix most problems on the first visit. Planetary mixers, slicers, food processors and dough equipment are built to last decades with the right service. We repair transmissions, motors, switches and safety interlocks.
Mixer, Slicer & Food Prep repair for Mint Hill businesses
Mint Hill's restaurants, grocery stores and medical facilities sit along Lawyers Road and Matthews-Mint Hill Road. We serve businesses near Lawyers Road, Matthews-Mint Hill Road and the Mint Hill town center, including ZIP codes 28227 in Mecklenburg County, NC.
Our technicians are in Mint Hill most days of the week, so a call from a business on the Mint Hill town center usually fits into the same day's route. We document every visit with the temperatures we measured and the parts we replaced, which helps Mint Hill managers with inspections and budgeting. Mecklenburg County health inspectors check cold-holding at 41°F or below and hot-holding at 135°F or above — we repair your mixer, slicer and food prep to hold those numbers. If a repair is not worth the money, we tell you and quote the replacement — no Mint Hill customer is pushed into a new unit they don't need.
Signs you need mixer, slicer and food prep repair
- Safety interlock fault
- Bowl lift not working
- Speeds slipping
- Grinding noise from the gearbox
- Slicer blade dull or wobbly
- Mixer won't start
What our technicians do
Worn gears, failed motors and switches, and broken safety interlocks are the most common fixes.
- Transmission and gear repair
- Electrical repair
- Motor replacement
- Bowl lift repair
- Slicer blade sharpening and bearing repair
- Switch and interlock repair
Save $50 on your repair
Book online or mention our website when you call and we take $50 off the repair. The service call is a flat $135, and you get a clear price before any work begins — no surprises.
Typical jobs we handle
Examples of common repairs on commercial refrigeration and kitchen equipment.
- Mixer, Slicer & Food PrepBakeries
Planetary mixer grinding in second speed
- What we found
- Worn transmission gear
- What we did
- Replaced the gear and lubricated the gearbox
✓ Usually needs a part ordered — two visits
- Reach-In RefrigeratorCafés & Coffee Shops
Dairy reach-in warm at the top shelf
- What we found
- Evaporator fan blade cracked, poor airflow
- What we did
- Replaced fan blade and motor, rebalanced airflow
✓ Typically fixed in one visit
- Reach-In FreezerPizzerias
Reach-in freezer frosting up every few days
- What we found
- Defrost heater open circuit
- What we did
- Replaced the defrost heater and tested a full defrost cycle
✓ Typically fixed in one visit
- Food Warmer & Holding CabinetCountry Clubs & Event Venues
Holding cabinet not heating before an event
- What we found
- Failed heating element
- What we did
- Replaced the element and tested the thermostat
✓ Typically fixed in one visit
- Soft Serve & Frozen Drink MachineIce Cream & Frozen Yogurt Shops
Soft serve coming out runny
- What we found
- Dirty condenser and worn drive belt
- What we did
- Cleaned the condenser, replaced the belt, adjusted viscosity
✓ Typically fixed in one visit
- Commercial OvenBakeries
Convection oven baking unevenly
- What we found
- Blower motor bearings worn
- What we did
- Replaced the convection blower motor
✓ Typically fixed in one visit
- Blast ChillerCatering & Commissary Kitchens
Blast chiller cycles taking too long
- What we found
- Food probe reading wrong and dirty condenser
- What we did
- Replaced the probe, cleaned the condenser
✓ Typically fixed in one visit
- Walk-In FreezerIce Cream & Frozen Yogurt Shops
Freezer drain line frozen, water pooling
- What we found
- Drain line heater burned out
- What we did
- Installed a new drain line heater and cleared the line
✓ Typically fixed in one visit
Examples for illustration. Every job is diagnosed on site; parts, time and price depend on the equipment.
Mixer, Slicer & Food Prep brands we repair in Mint Hill
Who we serve in Mint Hill
Technician tip
Never change mixer speeds while the motor is running — it strips gears.
Our warranty
Labor warranty on every repair.
Parts warranty on every part we install.
Extended warranty available on select repairs and installations. The exact term is written on your estimate before work starts.
Frequently asked questions
Is an older Hobart mixer worth repairing?
Almost always — older Hobart mixers are rebuildable and worth repairing.
Do you sharpen slicer blades?
Yes, as part of slicer service.
How much does mixer, slicer and food prep repair cost in Mint Hill, NC?
The service call is a flat $135, which covers the trip and diagnosis. After diagnosis you get a written price for the repair before any work starts, and you save $50 on the repair when you book online or mention our website.
What are your hours in Mint Hill?
We are open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). Call (980) 983-2911 or send a request online and the first available operator will call you back.
Do you serve ZIP code 28227?
Yes. We serve Mint Hill and all of Mint Hill, NC, including ZIP codes 28227.
Hours & contact
Commercial Appliances is open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). We serve Mint Hill, NC.
Phone: (980) 983-2911
Email: omnicommercialrefrigeration@gmail.com
Based in Charlotte, NC. We are a mobile service company — our technicians come to your business.
| Monday | 8:00 AM – 6:00 PM |
|---|---|
| Tuesday | 8:00 AM – 6:00 PM |
| Wednesday | 8:00 AM – 6:00 PM |
| Thursday | 8:00 AM – 6:00 PM |
| Friday | 8:00 AM – 6:00 PM |
| Saturday | 8:00 AM – 6:00 PM |
| Sunday | 10:00 AM – 3:00 PM |