Mixer, Slicer & Food Prep Repair in Indian Trail, NC
Indian Trail businesses call us for fast, honest mixer, slicer and food prep repair.
- Licensed & insuredCommercial refrigeration and kitchen equipment technicians
- $135 service callClear price before any work starts
- $50 off your repairWhen you book online or mention the website
- Warranty on every job30-day labor, 90-day parts, extended 1, 3 or 5 years on select work
- Open 7 days a weekMon–Sat 8 AM–6 PM · Sun 10 AM–3 PM
- Same-day serviceWhen you call early — trucks stocked with common parts
You get a flat $135 service call and a written price before any work starts. Planetary mixers, slicers, food processors and dough equipment are built to last decades with the right service. We repair transmissions, motors, switches and safety interlocks.
Mixer, Slicer & Food Prep repair for Indian Trail businesses
Indian Trail is one of Union County's fastest-growing towns, with new restaurants, grocery anchors and school kitchens opening every year. We serve businesses near US-74, Indian Trail Road and Wesley Chapel–Stouts Road, including ZIP codes 28079 in Union County, NC.
Our technicians are in Indian Trail most days of the week, so a call from a business on Wesley Chapel–Stouts Road usually fits into the same day's route. Union County health inspectors check cold-holding at 41°F or below and hot-holding at 135°F or above — we repair your mixer, slicer and food prep to hold those numbers. When a part is not on the truck, we order it the same day from Charlotte-area suppliers and come back to Indian Trail Road as soon as it arrives. Summer heat in the Charlotte region pushes condensers and compressors to their limit; for Indian Trail kitchens we check airflow, coil condition and electrical parts on every visit.
Signs you need mixer, slicer and food prep repair
- Slicer blade dull or wobbly
- Grinding noise from the gearbox
- Bowl lift not working
- Speeds slipping
- Mixer won't start
- Safety interlock fault
What our technicians do
Worn gears, failed motors and switches, and broken safety interlocks are the most common fixes.
- Motor replacement
- Bowl lift repair
- Electrical repair
- Switch and interlock repair
- Transmission and gear repair
- Slicer blade sharpening and bearing repair
Save $50 on your repair
Book online or mention our website when you call and we take $50 off the repair. The service call is a flat $135, and you get a clear price before any work begins — no surprises.
Typical jobs we handle
Examples of common repairs on commercial refrigeration and kitchen equipment.
- Mixer, Slicer & Food PrepBakeries
Planetary mixer grinding in second speed
- What we found
- Worn transmission gear
- What we did
- Replaced the gear and lubricated the gearbox
✓ Usually needs a part ordered — two visits
- Bar Cooler & Back BarBars & Nightclubs
Back-bar cooler bottles not cold
- What we found
- Thermostat out of calibration
- What we did
- Replaced the thermostat and set to 36°F
✓ Typically fixed in one visit
- Commercial OvenPizzerias
Conveyor pizza oven not reaching temperature
- What we found
- Failed igniter and flame sensor
- What we did
- Replaced igniter and sensor, verified bake temperature
✓ Typically fixed in one visit
- Ice MachineHotels & Banquet Facilities
Floor ice machine not harvesting
- What we found
- Faulty harvest assist and a weak water pump
- What we did
- Replaced both parts and ran test cycles
✓ Typically fixed in one visit
- Commercial OvenBakeries
Convection oven baking unevenly
- What we found
- Blower motor bearings worn
- What we did
- Replaced the convection blower motor
✓ Typically fixed in one visit
- Steamer, Kettle & Braising PanSchools & Universities
Steamer showing low-water alarm
- What we found
- Scaled water level probe
- What we did
- Cleaned the probe and delimed the generator
✓ Typically fixed in one visit
- Walk-In CoolerGrocery Stores & Supermarkets
Walk-in cooler slowly warming over several days
- What we found
- Condenser coil packed with dust and cottonwood; high head pressure
- What we did
- Deep-cleaned the condenser, checked charge and amperage
✓ Typically fixed in one visit
- Draft Beer & Keg CoolerBreweries & Taprooms
Foamy pours on every tap
- What we found
- Glycol chiller pump failing, lines warming
- What we did
- Replaced the glycol pump and topped up glycol
✓ Typically fixed in one visit
Examples for illustration. Every job is diagnosed on site; parts, time and price depend on the equipment.
Mixer, Slicer & Food Prep brands we repair in Indian Trail
Who we serve in Indian Trail
Technician tip
Never change mixer speeds while the motor is running — it strips gears.
Our warranty
Labor warranty on every repair.
Parts warranty on every part we install.
Extended warranty available on select repairs and installations. The exact term is written on your estimate before work starts.
Frequently asked questions
Is an older Hobart mixer worth repairing?
Almost always — older Hobart mixers are rebuildable and worth repairing.
Do you sharpen slicer blades?
Yes, as part of slicer service.
How much does mixer, slicer and food prep repair cost in Indian Trail, NC?
The service call is a flat $135, which covers the trip and diagnosis. After diagnosis you get a written price for the repair before any work starts, and you save $50 on the repair when you book online or mention our website.
What are your hours in Indian Trail?
We are open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). Call (980) 983-2911 or send a request online and the first available operator will call you back.
Do you serve ZIP code 28079?
Yes. We serve Indian Trail and all of Indian Trail, NC, including ZIP codes 28079.
Hours & contact
Commercial Appliances is open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). We serve Indian Trail, NC.
Phone: (980) 983-2911
Email: omnicommercialrefrigeration@gmail.com
Based in Charlotte, NC. We are a mobile service company — our technicians come to your business.
| Monday | 8:00 AM – 6:00 PM |
|---|---|
| Tuesday | 8:00 AM – 6:00 PM |
| Wednesday | 8:00 AM – 6:00 PM |
| Thursday | 8:00 AM – 6:00 PM |
| Friday | 8:00 AM – 6:00 PM |
| Saturday | 8:00 AM – 6:00 PM |
| Sunday | 10:00 AM – 3:00 PM |