Mixer, Slicer & Food Prep Repair in Matthews, NC
Looking for reliable mixer, slicer and food prep repair near downtown Matthews on Trade Street? We serve Matthews, NC with same-day service when available.
- Licensed & insuredCommercial refrigeration and kitchen equipment technicians
- $135 service callClear price before any work starts
- $50 off your repairWhen you book online or mention the website
- Warranty on every job30-day labor, 90-day parts, extended 1, 3 or 5 years on select work
- Open 7 days a weekMon–Sat 8 AM–6 PM · Sun 10 AM–3 PM
- Same-day serviceWhen you call early — trucks stocked with common parts
Planetary mixers, slicers, food processors and dough equipment are built to last decades with the right service. We repair transmissions, motors, switches and safety interlocks.
Mixer, Slicer & Food Prep repair for Matthews businesses
Matthews combines a walkable downtown restaurant row with heavy retail along US-74 and a busy medical corridor. We serve businesses near downtown Matthews on Trade Street, Independence Boulevard (US-74) and Sycamore Commons, including ZIP codes 28104, 28105 in Mecklenburg County, NC.
Our technicians are in Matthews most days of the week, so a call from a business on Sycamore Commons usually fits into the same day's route. Mecklenburg County health inspectors check cold-holding at 41°F or below and hot-holding at 135°F or above — we repair your mixer, slicer and food prep to hold those numbers. If a repair is not worth the money, we tell you and quote the replacement — no Matthews customer is pushed into a new unit they don't need. We document every visit with the temperatures we measured and the parts we replaced, which helps Matthews managers with inspections and budgeting.
Signs you need mixer, slicer and food prep repair
- Slicer blade dull or wobbly
- Bowl lift not working
- Safety interlock fault
- Grinding noise from the gearbox
- Mixer won't start
- Speeds slipping
What our technicians do
Worn gears, failed motors and switches, and broken safety interlocks are the most common fixes.
- Switch and interlock repair
- Motor replacement
- Transmission and gear repair
- Slicer blade sharpening and bearing repair
- Bowl lift repair
- Electrical repair
Save $50 on your repair
Book online or mention our website when you call and we take $50 off the repair. The service call is a flat $135, and you get a clear price before any work begins — no surprises.
Typical jobs we handle
Examples of common repairs on commercial refrigeration and kitchen equipment.
- Mixer, Slicer & Food PrepBakeries
Planetary mixer grinding in second speed
- What we found
- Worn transmission gear
- What we did
- Replaced the gear and lubricated the gearbox
✓ Usually needs a part ordered — two visits
- Undercounter & Worktop RefrigeratorRestaurants
Chef base losing temperature during the rush
- What we found
- Front grille and condenser clogged with grease
- What we did
- Cleaned the condenser, replaced a worn drawer gasket
✓ Typically fixed in one visit
- Reach-In RefrigeratorRestaurants
Two-door reach-in at 45°F on the line
- What we found
- Condenser fan motor not running
- What we did
- Replaced the condenser fan motor and cleaned the coil
✓ Typically fixed in one visit
- Coffee & Beverage EquipmentCafés & Coffee Shops
Coffee brewer not hot
- What we found
- Scale-coated heating element
- What we did
- Replaced the element, descaled the tank
✓ Typically fixed in one visit
- Prep Table & Sandwich UnitRestaurants
Sandwich unit lid won't stay open
- What we found
- Broken lid hinge pin
- What we did
- Replaced the hinge set and adjusted the lid
✓ Typically fixed the same day
- Prep Table & Sandwich UnitPizzerias
Pizza prep table rail pans at 46°F
- What we found
- Dirty condenser and weak evaporator fan
- What we did
- Cleaned the condenser, replaced the fan motor, rail back to 39°F
✓ Typically fixed in one visit
- Commercial DishwasherHotels & Banquet Facilities
Dish machine final rinse at 160°F
- What we found
- Booster heater element burned out
- What we did
- Replaced the element, verified 180°F final rinse
✓ Typically fixed in one visit
- Condensing Unit & CompressorGrocery Stores & Supermarkets
Rooftop condensing unit tripping the breaker
- What we found
- Shorted condenser fan motor
- What we did
- Replaced the fan motor and checked electrical connections
✓ Typically fixed in one visit
Examples for illustration. Every job is diagnosed on site; parts, time and price depend on the equipment.
Mixer, Slicer & Food Prep brands we repair in Matthews
Who we serve in Matthews
Mixer, Slicer & Food Prep repair nearby
Technician tip
Never change mixer speeds while the motor is running — it strips gears.
Our warranty
Labor warranty on every repair.
Parts warranty on every part we install.
Extended warranty available on select repairs and installations. The exact term is written on your estimate before work starts.
Frequently asked questions
Is an older Hobart mixer worth repairing?
Almost always — older Hobart mixers are rebuildable and worth repairing.
Do you sharpen slicer blades?
Yes, as part of slicer service.
How much does mixer, slicer and food prep repair cost in Matthews, NC?
The service call is a flat $135, which covers the trip and diagnosis. After diagnosis you get a written price for the repair before any work starts, and you save $50 on the repair when you book online or mention our website.
What are your hours in Matthews?
We are open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). Call (980) 983-2911 or send a request online and the first available operator will call you back.
Do you serve ZIP code 28104?
Yes. We serve Matthews and all of Matthews, NC, including ZIP codes 28104, 28105.
Hours & contact
Commercial Appliances is open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). We serve Matthews, NC.
Phone: (980) 983-2911
Email: omnicommercialrefrigeration@gmail.com
Based in Charlotte, NC. We are a mobile service company — our technicians come to your business.
| Monday | 8:00 AM – 6:00 PM |
|---|---|
| Tuesday | 8:00 AM – 6:00 PM |
| Wednesday | 8:00 AM – 6:00 PM |
| Thursday | 8:00 AM – 6:00 PM |
| Friday | 8:00 AM – 6:00 PM |
| Saturday | 8:00 AM – 6:00 PM |
| Sunday | 10:00 AM – 3:00 PM |