Mixer, Slicer & Food Prep Repair in South End, Charlotte
Need mixer, slicer and food prep repair in South End, Charlotte? We send commercial technicians to restaurants, bars, stores and institutional kitchens across South End every week.
- Licensed & insuredCommercial refrigeration and kitchen equipment technicians
- $135 service callClear price before any work starts
- $50 off your repairWhen you book online or mention the website
- Warranty on every job30-day labor, 90-day parts, extended 1, 3 or 5 years on select work
- Open 7 days a weekMon–Sat 8 AM–6 PM · Sun 10 AM–3 PM
- Same-day serviceWhen you call early — trucks stocked with common parts
Planetary mixers, slicers, food processors and dough equipment are built to last decades with the right service. We repair transmissions, motors, switches and safety interlocks.
Mixer, Slicer & Food Prep repair for South End businesses
South End is packed with breweries, taprooms, cafés and new restaurants along the light rail — draft systems, ice machines and bar coolers are everywhere. We serve businesses near the Rail Trail, Camden Road and South Boulevard, including ZIP codes 28203 in Mecklenburg County, NC.
Mecklenburg County health inspectors check cold-holding at 41°F or below and hot-holding at 135°F or above — we repair your mixer, slicer and food prep to hold those numbers. Businesses in ZIP 28203 can book online in 30 seconds, and the first available operator calls back during business hours. We document every visit with the temperatures we measured and the parts we replaced, which helps South End managers with inspections and budgeting. When a part is not on the truck, we order it the same day from Charlotte-area suppliers and come back to Camden Road as soon as it arrives.
Signs you need mixer, slicer and food prep repair
- Speeds slipping
- Safety interlock fault
- Bowl lift not working
- Mixer won't start
- Slicer blade dull or wobbly
- Grinding noise from the gearbox
What our technicians do
Worn gears, failed motors and switches, and broken safety interlocks are the most common fixes.
- Transmission and gear repair
- Electrical repair
- Bowl lift repair
- Slicer blade sharpening and bearing repair
- Motor replacement
- Switch and interlock repair
Save $50 on your repair
Book online or mention our website when you call and we take $50 off the repair. The service call is a flat $135, and you get a clear price before any work begins — no surprises.
Typical jobs we handle
Examples of common repairs on commercial refrigeration and kitchen equipment.
- Mixer, Slicer & Food PrepBakeries
Planetary mixer grinding in second speed
- What we found
- Worn transmission gear
- What we did
- Replaced the gear and lubricated the gearbox
✓ Usually needs a part ordered — two visits
- Commercial OvenBakeries
Convection oven baking unevenly
- What we found
- Blower motor bearings worn
- What we did
- Replaced the convection blower motor
✓ Typically fixed in one visit
- Ice MachineBars & Nightclubs
Ice machine making half the usual ice
- What we found
- Heavy scale on the evaporator plate
- What we did
- Descaled, sanitized and replaced the water filter
✓ Typically fixed in one visit
- Bar Cooler & Back BarBars & Nightclubs
Back-bar cooler bottles not cold
- What we found
- Thermostat out of calibration
- What we did
- Replaced the thermostat and set to 36°F
✓ Typically fixed in one visit
- Ice MachineHotels & Banquet Facilities
Floor ice machine not harvesting
- What we found
- Faulty harvest assist and a weak water pump
- What we did
- Replaced both parts and ran test cycles
✓ Typically fixed in one visit
- Food Warmer & Holding CabinetCountry Clubs & Event Venues
Holding cabinet not heating before an event
- What we found
- Failed heating element
- What we did
- Replaced the element and tested the thermostat
✓ Typically fixed in one visit
- Walk-In CoolerBreweries & Taprooms
Keg walk-in short-cycling on hot afternoons
- What we found
- Failed run capacitor and pitted contactor
- What we did
- Replaced capacitor and contactor, tested compressor under load
✓ Typically fixed in one visit
- Walk-In CoolerGrocery Stores & Supermarkets
Walk-in cooler slowly warming over several days
- What we found
- Condenser coil packed with dust and cottonwood; high head pressure
- What we did
- Deep-cleaned the condenser, checked charge and amperage
✓ Typically fixed in one visit
Examples for illustration. Every job is diagnosed on site; parts, time and price depend on the equipment.
Mixer, Slicer & Food Prep brands we repair in South End
Who we serve in South End
Technician tip
Never change mixer speeds while the motor is running — it strips gears.
Our warranty
Labor warranty on every repair.
Parts warranty on every part we install.
Extended warranty available on select repairs and installations. The exact term is written on your estimate before work starts.
Frequently asked questions
Is an older Hobart mixer worth repairing?
Almost always — older Hobart mixers are rebuildable and worth repairing.
Do you sharpen slicer blades?
Yes, as part of slicer service.
How much does mixer, slicer and food prep repair cost in South End, Charlotte?
The service call is a flat $135, which covers the trip and diagnosis. After diagnosis you get a written price for the repair before any work starts, and you save $50 on the repair when you book online or mention our website.
What are your hours in South End?
We are open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). Call (980) 983-2911 or send a request online and the first available operator will call you back.
Do you serve ZIP code 28203?
Yes. We serve South End and all of South End, Charlotte, including ZIP codes 28203.
Hours & contact
Commercial Appliances is open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). We serve South End, Charlotte.
Phone: (980) 983-2911
Email: omnicommercialrefrigeration@gmail.com
Based in Charlotte, NC. We are a mobile service company — our technicians come to your business.
| Monday | 8:00 AM – 6:00 PM |
|---|---|
| Tuesday | 8:00 AM – 6:00 PM |
| Wednesday | 8:00 AM – 6:00 PM |
| Thursday | 8:00 AM – 6:00 PM |
| Friday | 8:00 AM – 6:00 PM |
| Saturday | 8:00 AM – 6:00 PM |
| Sunday | 10:00 AM – 3:00 PM |