Mixer, Slicer & Food Prep Repair in Providence Plantation, Charlotte
Our mixer, slicer and food prep repair service covers all of Providence Plantation, Charlotte.
- Licensed & insuredCommercial refrigeration and kitchen equipment technicians
- $135 service callClear price before any work starts
- $50 off your repairWhen you book online or mention the website
- Warranty on every job30-day labor, 90-day parts, extended 1, 3 or 5 years on select work
- Open 7 days a weekMon–Sat 8 AM–6 PM · Sun 10 AM–3 PM
- Same-day serviceWhen you call early — trucks stocked with common parts
We know the local businesses, the building types and how hot a Providence Plantation kitchen gets in July. Planetary mixers, slicers, food processors and dough equipment are built to last decades with the right service. We repair transmissions, motors, switches and safety interlocks.
Mixer, Slicer & Food Prep repair for Providence Plantation businesses
Providence Plantation's shopping centers along Providence Road serve fast-growing south Charlotte. We serve businesses near Providence Road, the Providence Road and I-485 interchange and Ardrey Kell Road, including ZIP codes 28270, 28277 in Mecklenburg County, NC.
From quick-service counters near Ardrey Kell Road to full kitchens near Providence Road, Providence Plantation businesses rely on us for mixer, slicer and food prep work. Mecklenburg County health inspectors check cold-holding at 41°F or below and hot-holding at 135°F or above — we repair your mixer, slicer and food prep to hold those numbers. Summer heat in the Charlotte region pushes condensers and compressors to their limit; for Providence Plantation kitchens we check airflow, coil condition and electrical parts on every visit. Businesses in ZIP 28270 and 28277 can book online in 30 seconds, and the first available operator calls back during business hours.
Signs you need mixer, slicer and food prep repair
- Mixer won't start
- Bowl lift not working
- Safety interlock fault
- Speeds slipping
- Grinding noise from the gearbox
- Slicer blade dull or wobbly
What our technicians do
Worn gears, failed motors and switches, and broken safety interlocks are the most common fixes.
- Bowl lift repair
- Motor replacement
- Slicer blade sharpening and bearing repair
- Switch and interlock repair
- Transmission and gear repair
- Electrical repair
Save $50 on your repair
Book online or mention our website when you call and we take $50 off the repair. The service call is a flat $135, and you get a clear price before any work begins — no surprises.
Typical jobs we handle
Examples of common repairs on commercial refrigeration and kitchen equipment.
- Mixer, Slicer & Food PrepBakeries
Planetary mixer grinding in second speed
- What we found
- Worn transmission gear
- What we did
- Replaced the gear and lubricated the gearbox
✓ Usually needs a part ordered — two visits
- Commercial FryerConvenience Stores & Gas Stations
Fryer overheating and tripping the high-limit
- What we found
- Temperature probe failing
- What we did
- Replaced the probe and calibrated the controller
✓ Typically fixed in one visit
- Commercial OvenPizzerias
Conveyor pizza oven not reaching temperature
- What we found
- Failed igniter and flame sensor
- What we did
- Replaced igniter and sensor, verified bake temperature
✓ Typically fixed in one visit
- Blast ChillerCatering & Commissary Kitchens
Blast chiller cycles taking too long
- What we found
- Food probe reading wrong and dirty condenser
- What we did
- Replaced the probe, cleaned the condenser
✓ Typically fixed in one visit
- Walk-In CoolerBreweries & Taprooms
Keg walk-in short-cycling on hot afternoons
- What we found
- Failed run capacitor and pitted contactor
- What we did
- Replaced capacitor and contactor, tested compressor under load
✓ Typically fixed in one visit
- Steamer, Kettle & Braising PanSchools & Universities
Steamer showing low-water alarm
- What we found
- Scaled water level probe
- What we did
- Cleaned the probe and delimed the generator
✓ Typically fixed in one visit
- Walk-In CoolerGrocery Stores & Supermarkets
Walk-in cooler slowly warming over several days
- What we found
- Condenser coil packed with dust and cottonwood; high head pressure
- What we did
- Deep-cleaned the condenser, checked charge and amperage
✓ Typically fixed in one visit
- Ice MachineHotels & Banquet Facilities
Floor ice machine not harvesting
- What we found
- Faulty harvest assist and a weak water pump
- What we did
- Replaced both parts and ran test cycles
✓ Typically fixed in one visit
Examples for illustration. Every job is diagnosed on site; parts, time and price depend on the equipment.
Mixer, Slicer & Food Prep brands we repair in Providence Plantation
Who we serve in Providence Plantation
Technician tip
Never change mixer speeds while the motor is running — it strips gears.
Our warranty
Labor warranty on every repair.
Parts warranty on every part we install.
Extended warranty available on select repairs and installations. The exact term is written on your estimate before work starts.
Frequently asked questions
Is an older Hobart mixer worth repairing?
Almost always — older Hobart mixers are rebuildable and worth repairing.
Do you sharpen slicer blades?
Yes, as part of slicer service.
How much does mixer, slicer and food prep repair cost in Providence Plantation, Charlotte?
The service call is a flat $135, which covers the trip and diagnosis. After diagnosis you get a written price for the repair before any work starts, and you save $50 on the repair when you book online or mention our website.
What are your hours in Providence Plantation?
We are open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). Call (980) 983-2911 or send a request online and the first available operator will call you back.
Do you serve ZIP code 28270?
Yes. We serve Providence Plantation and all of Providence Plantation, Charlotte, including ZIP codes 28270, 28277.
Hours & contact
Commercial Appliances is open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). We serve Providence Plantation, Charlotte.
Phone: (980) 983-2911
Email: omnicommercialrefrigeration@gmail.com
Based in Charlotte, NC. We are a mobile service company — our technicians come to your business.
| Monday | 8:00 AM – 6:00 PM |
|---|---|
| Tuesday | 8:00 AM – 6:00 PM |
| Wednesday | 8:00 AM – 6:00 PM |
| Thursday | 8:00 AM – 6:00 PM |
| Friday | 8:00 AM – 6:00 PM |
| Saturday | 8:00 AM – 6:00 PM |
| Sunday | 10:00 AM – 3:00 PM |