Mixer, Slicer & Food Prep Repair in Piper Glen, Charlotte
Piper Glen businesses call us for fast, honest mixer, slicer and food prep repair.
- Licensed & insuredCommercial refrigeration and kitchen equipment technicians
- $135 service callClear price before any work starts
- $50 off your repairWhen you book online or mention the website
- Warranty on every job30-day labor, 90-day parts, extended 1, 3 or 5 years on select work
- Open 7 days a weekMon–Sat 8 AM–6 PM · Sun 10 AM–3 PM
- Same-day serviceWhen you call early — trucks stocked with common parts
You get a flat $135 service call and a written price before any work starts. Planetary mixers, slicers, food processors and dough equipment are built to last decades with the right service. We repair transmissions, motors, switches and safety interlocks.
Mixer, Slicer & Food Prep repair for Piper Glen businesses
Piper Glen sits between Ballantyne and Blakeney, close to country clubs and restaurant corridors on Rea Road. We serve businesses near Rea Road, Piper Glen Drive and Carmel Road, including ZIP codes 28277 in Mecklenburg County, NC.
From quick-service counters near Carmel Road to full kitchens near Rea Road, Piper Glen businesses rely on us for mixer, slicer and food prep work. When a part is not on the truck, we order it the same day from Charlotte-area suppliers and come back to Piper Glen Drive as soon as it arrives. Our technicians are in Piper Glen most days of the week, so a call from a business on Carmel Road usually fits into the same day's route. Mecklenburg County health inspectors check cold-holding at 41°F or below and hot-holding at 135°F or above — we repair your mixer, slicer and food prep to hold those numbers.
Signs you need mixer, slicer and food prep repair
- Grinding noise from the gearbox
- Slicer blade dull or wobbly
- Speeds slipping
- Safety interlock fault
- Mixer won't start
- Bowl lift not working
What our technicians do
Worn gears, failed motors and switches, and broken safety interlocks are the most common fixes.
- Bowl lift repair
- Slicer blade sharpening and bearing repair
- Switch and interlock repair
- Transmission and gear repair
- Motor replacement
- Electrical repair
Save $50 on your repair
Book online or mention our website when you call and we take $50 off the repair. The service call is a flat $135, and you get a clear price before any work begins — no surprises.
Typical jobs we handle
Examples of common repairs on commercial refrigeration and kitchen equipment.
- Mixer, Slicer & Food PrepBakeries
Planetary mixer grinding in second speed
- What we found
- Worn transmission gear
- What we did
- Replaced the gear and lubricated the gearbox
✓ Usually needs a part ordered — two visits
- Ice MachineHospitals & Senior Living
Nugget ice machine leaking onto the floor
- What we found
- Cracked drain hose behind the unit
- What we did
- Replaced the hose, cleaned and sanitized the machine
✓ Typically fixed in one visit
- Prep Table & Sandwich UnitPizzerias
Pizza prep table rail pans at 46°F
- What we found
- Dirty condenser and weak evaporator fan
- What we did
- Cleaned the condenser, replaced the fan motor, rail back to 39°F
✓ Typically fixed in one visit
- Walk-In CoolerBreweries & Taprooms
Keg walk-in short-cycling on hot afternoons
- What we found
- Failed run capacitor and pitted contactor
- What we did
- Replaced capacitor and contactor, tested compressor under load
✓ Typically fixed in one visit
- Walk-In FreezerSchools & Universities
Ice building up on the freezer floor near the door
- What we found
- Torn door gasket and failed door-frame heater
- What we did
- Replaced the gasket and frame heater wire
✓ Typically fixed in one visit
- Blast ChillerCatering & Commissary Kitchens
Blast chiller cycles taking too long
- What we found
- Food probe reading wrong and dirty condenser
- What we did
- Replaced the probe, cleaned the condenser
✓ Typically fixed in one visit
- Soft Serve & Frozen Drink MachineIce Cream & Frozen Yogurt Shops
Soft serve coming out runny
- What we found
- Dirty condenser and worn drive belt
- What we did
- Cleaned the condenser, replaced the belt, adjusted viscosity
✓ Typically fixed in one visit
- Ice MachineHotels & Banquet Facilities
Floor ice machine not harvesting
- What we found
- Faulty harvest assist and a weak water pump
- What we did
- Replaced both parts and ran test cycles
✓ Typically fixed in one visit
Examples for illustration. Every job is diagnosed on site; parts, time and price depend on the equipment.
Mixer, Slicer & Food Prep brands we repair in Piper Glen
Who we serve in Piper Glen
Technician tip
Never change mixer speeds while the motor is running — it strips gears.
Our warranty
Labor warranty on every repair.
Parts warranty on every part we install.
Extended warranty available on select repairs and installations. The exact term is written on your estimate before work starts.
Frequently asked questions
Is an older Hobart mixer worth repairing?
Almost always — older Hobart mixers are rebuildable and worth repairing.
Do you sharpen slicer blades?
Yes, as part of slicer service.
How much does mixer, slicer and food prep repair cost in Piper Glen, Charlotte?
The service call is a flat $135, which covers the trip and diagnosis. After diagnosis you get a written price for the repair before any work starts, and you save $50 on the repair when you book online or mention our website.
What are your hours in Piper Glen?
We are open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). Call (980) 983-2911 or send a request online and the first available operator will call you back.
Do you serve ZIP code 28277?
Yes. We serve Piper Glen and all of Piper Glen, Charlotte, including ZIP codes 28277.
Hours & contact
Commercial Appliances is open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). We serve Piper Glen, Charlotte.
Phone: (980) 983-2911
Email: omnicommercialrefrigeration@gmail.com
Based in Charlotte, NC. We are a mobile service company — our technicians come to your business.
| Monday | 8:00 AM – 6:00 PM |
|---|---|
| Tuesday | 8:00 AM – 6:00 PM |
| Wednesday | 8:00 AM – 6:00 PM |
| Thursday | 8:00 AM – 6:00 PM |
| Friday | 8:00 AM – 6:00 PM |
| Saturday | 8:00 AM – 6:00 PM |
| Sunday | 10:00 AM – 3:00 PM |