Fryer Pilot Keeps Going Out — Repair in Matthews, NC
Fryer Pilot Keeps Going Out in Matthews, NC? Our commercial fryer repair service covers all of Matthews, NC.
- Licensed & insuredCommercial refrigeration and kitchen equipment technicians
- $135 service callClear price before any work starts
- $50 off your repairWhen you book online or mention the website
- Warranty on every job30-day labor, 90-day parts, extended 1, 3 or 5 years on select work
- Open 7 days a weekMon–Sat 8 AM–6 PM · Sun 10 AM–3 PM
- Same-day serviceWhen you call early — trucks stocked with common parts
We know the local businesses, the building types and how hot a Matthews kitchen gets in July.
Likely causes
- Weak thermopile or thermocouple
- Dirty pilot orifice
- Gas valve failure
- Drafts from hood
What to do before we arrive
- Relight per the label
- Check for strong drafts
- Don't keep relighting if it won't hold
Local service
We serve businesses near downtown Matthews on Trade Street, Independence Boulevard (US-74) and Sycamore Commons, including ZIP codes 28104, 28105 in Mecklenburg County, NC.
Our technicians are in Matthews most days of the week, so a call from a business on Sycamore Commons usually fits into the same day's route. We document every visit with the temperatures we measured and the parts we replaced, which helps Matthews managers with inspections and budgeting. Mecklenburg County health inspectors check cold-holding at 41°F or below and hot-holding at 135°F or above — we repair your commercial fryer to hold those numbers. Many of our Matthews customers are along downtown Matthews on Trade Street and Matthews Township Parkway, where busy kitchens run commercial fryer equipment hard from open to close.
Save $50 on your repair
Book online or mention our website when you call and we take $50 off the repair. The service call is a flat $135, and you get a clear price before any work begins — no surprises.
Typical jobs we handle
Examples of common repairs on commercial refrigeration and kitchen equipment.
- Commercial FryerRestaurants
Fryer won't heat before lunch
- What we found
- Weak thermopile
- What we did
- Replaced the thermopile and tested the gas valve
✓ Typically fixed in one visit
- Commercial FryerConvenience Stores & Gas Stations
Fryer overheating and tripping the high-limit
- What we found
- Temperature probe failing
- What we did
- Replaced the probe and calibrated the controller
✓ Typically fixed in one visit
- Walk-In CoolerRestaurants
Walk-in cooler at 48°F before dinner service
- What we found
- Evaporator fan motor seized; coil starting to ice
- What we did
- Replaced the fan motor, cleared the coil, verified 36°F box temperature
✓ Typically fixed in one visit
- Reach-In RefrigeratorCafés & Coffee Shops
Dairy reach-in warm at the top shelf
- What we found
- Evaporator fan blade cracked, poor airflow
- What we did
- Replaced fan blade and motor, rebalanced airflow
✓ Typically fixed in one visit
- Walk-In FreezerIce Cream & Frozen Yogurt Shops
Freezer drain line frozen, water pooling
- What we found
- Drain line heater burned out
- What we did
- Installed a new drain line heater and cleared the line
✓ Typically fixed in one visit
- Bar Cooler & Back BarBars & Nightclubs
Back-bar cooler bottles not cold
- What we found
- Thermostat out of calibration
- What we did
- Replaced the thermostat and set to 36°F
✓ Typically fixed in one visit
- Refrigerated Display CaseBakeries
Bakery display case warm at the front
- What we found
- Evaporator iced from a bad defrost timer
- What we did
- Replaced the timer, defrosted, verified temperatures
✓ Typically fixed in one visit
- Food Warmer & Holding CabinetCountry Clubs & Event Venues
Holding cabinet not heating before an event
- What we found
- Failed heating element
- What we did
- Replaced the element and tested the thermostat
✓ Typically fixed in one visit
Examples for illustration. Every job is diagnosed on site; parts, time and price depend on the equipment.
Frequently asked questions
Why is my fryer pilot keeps going out?
Most often: weak thermopile or thermocouple; dirty pilot orifice; drafts from hood; gas valve failure.
How much does commercial fryer repair cost in Matthews, NC?
The service call is a flat $135, which covers the trip and diagnosis. After diagnosis you get a written price for the repair before any work starts, and you save $50 on the repair when you book online or mention our website.
What are your hours in Matthews?
We are open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). Call (980) 983-2911 or send a request online and the first available operator will call you back.
Do you serve ZIP code 28104?
Yes. We serve Matthews and all of Matthews, NC, including ZIP codes 28104, 28105.
Hours & contact
Commercial Appliances is open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). We serve Matthews, NC.
Phone: (980) 983-2911
Email: omnicommercialrefrigeration@gmail.com
Based in Charlotte, NC. We are a mobile service company — our technicians come to your business.
| Monday | 8:00 AM – 6:00 PM |
|---|---|
| Tuesday | 8:00 AM – 6:00 PM |
| Wednesday | 8:00 AM – 6:00 PM |
| Thursday | 8:00 AM – 6:00 PM |
| Friday | 8:00 AM – 6:00 PM |
| Saturday | 8:00 AM – 6:00 PM |
| Sunday | 10:00 AM – 3:00 PM |