Mixer, Slicer & Food Prep Repair in Fort Mill, SC
Fort Mill businesses call us for fast, honest mixer, slicer and food prep repair.
- Licensed & insuredCommercial refrigeration and kitchen equipment technicians
- $135 service callClear price before any work starts
- $50 off your repairWhen you book online or mention the website
- Warranty on every job30-day labor, 90-day parts, extended 1, 3 or 5 years on select work
- Open 7 days a weekMon–Sat 8 AM–6 PM · Sun 10 AM–3 PM
- Same-day serviceWhen you call early — trucks stocked with common parts
You get a flat $135 service call and a written price before any work starts. Planetary mixers, slicers, food processors and dough equipment are built to last decades with the right service. We repair transmissions, motors, switches and safety interlocks.
Mixer, Slicer & Food Prep repair for Fort Mill businesses
Fort Mill, just across the state line, has fast-growing restaurant, hotel and grocery development along I-77 and in its town centers. We serve businesses near Main Street, Baxter Village and Kingsley Town Center, including ZIP codes 29707, 29708, 29715 in York County, SC.
Our technicians are in Fort Mill most days of the week, so a call from a business on Kingsley Town Center usually fits into the same day's route. When a part is not on the truck, we order it the same day from Charlotte-area suppliers and come back to Baxter Village as soon as it arrives. York County health inspectors check cold-holding at 41°F or below and hot-holding at 135°F or above — we repair your mixer, slicer and food prep to hold those numbers. From quick-service counters near Kingsley Town Center to full kitchens near Main Street, Fort Mill businesses rely on us for mixer, slicer and food prep work.
Signs you need mixer, slicer and food prep repair
- Mixer won't start
- Speeds slipping
- Slicer blade dull or wobbly
- Grinding noise from the gearbox
- Safety interlock fault
- Bowl lift not working
What our technicians do
Worn gears, failed motors and switches, and broken safety interlocks are the most common fixes.
- Electrical repair
- Switch and interlock repair
- Slicer blade sharpening and bearing repair
- Bowl lift repair
- Transmission and gear repair
- Motor replacement
Save $50 on your repair
Book online or mention our website when you call and we take $50 off the repair. The service call is a flat $135, and you get a clear price before any work begins — no surprises.
Typical jobs we handle
Examples of common repairs on commercial refrigeration and kitchen equipment.
- Mixer, Slicer & Food PrepBakeries
Planetary mixer grinding in second speed
- What we found
- Worn transmission gear
- What we did
- Replaced the gear and lubricated the gearbox
✓ Usually needs a part ordered — two visits
- Griddle & CharbroilerFood Trucks
Griddle has a cold spot on one side
- What we found
- Clogged burner ports
- What we did
- Cleaned and adjusted the burner, checked the thermostat
✓ Typically fixed in one visit
- Walk-In CoolerGrocery Stores & Supermarkets
Walk-in cooler slowly warming over several days
- What we found
- Condenser coil packed with dust and cottonwood; high head pressure
- What we did
- Deep-cleaned the condenser, checked charge and amperage
✓ Typically fixed in one visit
- Commercial OvenBakeries
Convection oven baking unevenly
- What we found
- Blower motor bearings worn
- What we did
- Replaced the convection blower motor
✓ Typically fixed in one visit
- Food Warmer & Holding CabinetCountry Clubs & Event Venues
Holding cabinet not heating before an event
- What we found
- Failed heating element
- What we did
- Replaced the element and tested the thermostat
✓ Typically fixed in one visit
- Prep Table & Sandwich UnitRestaurants
Sandwich unit lid won't stay open
- What we found
- Broken lid hinge pin
- What we did
- Replaced the hinge set and adjusted the lid
✓ Typically fixed the same day
- Steamer, Kettle & Braising PanSchools & Universities
Steamer showing low-water alarm
- What we found
- Scaled water level probe
- What we did
- Cleaned the probe and delimed the generator
✓ Typically fixed in one visit
- Soft Serve & Frozen Drink MachineIce Cream & Frozen Yogurt Shops
Soft serve coming out runny
- What we found
- Dirty condenser and worn drive belt
- What we did
- Cleaned the condenser, replaced the belt, adjusted viscosity
✓ Typically fixed in one visit
Examples for illustration. Every job is diagnosed on site; parts, time and price depend on the equipment.
Mixer, Slicer & Food Prep brands we repair in Fort Mill
Who we serve in Fort Mill
Mixer, Slicer & Food Prep repair nearby
Technician tip
Never change mixer speeds while the motor is running — it strips gears.
Our warranty
Labor warranty on every repair.
Parts warranty on every part we install.
Extended warranty available on select repairs and installations. The exact term is written on your estimate before work starts.
Frequently asked questions
Is an older Hobart mixer worth repairing?
Almost always — older Hobart mixers are rebuildable and worth repairing.
Do you sharpen slicer blades?
Yes, as part of slicer service.
How much does mixer, slicer and food prep repair cost in Fort Mill, SC?
The service call is a flat $135, which covers the trip and diagnosis. After diagnosis you get a written price for the repair before any work starts, and you save $50 on the repair when you book online or mention our website.
What are your hours in Fort Mill?
We are open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). Call (980) 983-2911 or send a request online and the first available operator will call you back.
Do you serve ZIP code 29707?
Yes. We serve Fort Mill and all of Fort Mill, SC, including ZIP codes 29707, 29708, 29715.
Hours & contact
Commercial Appliances is open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). We serve Fort Mill, SC.
Phone: (980) 983-2911
Email: omnicommercialrefrigeration@gmail.com
Based in Charlotte, NC. We are a mobile service company — our technicians come to your business.
| Monday | 8:00 AM – 6:00 PM |
|---|---|
| Tuesday | 8:00 AM – 6:00 PM |
| Wednesday | 8:00 AM – 6:00 PM |
| Thursday | 8:00 AM – 6:00 PM |
| Friday | 8:00 AM – 6:00 PM |
| Saturday | 8:00 AM – 6:00 PM |
| Sunday | 10:00 AM – 3:00 PM |