Hobart Repair in Fort Mill, SC
Our Hobart repair service covers all of Fort Mill, SC.
- Licensed & insuredCommercial refrigeration and kitchen equipment technicians
- $135 service callClear price before any work starts
- $50 off your repairWhen you book online or mention the website
- Warranty on every job30-day labor, 90-day parts, extended 1, 3 or 5 years on select work
- Open 7 days a weekMon–Sat 8 AM–6 PM · Sun 10 AM–3 PM
- Same-day serviceWhen you call early — trucks stocked with common parts
We know the local businesses, the building types and how hot a Fort Mill kitchen gets in July. Hobart makes dishwashers, mixers and slicers, and we repair them on-site.
Hobart service for Fort Mill businesses
Fort Mill, just across the state line, has fast-growing restaurant, hotel and grocery development along I-77 and in its town centers. We serve businesses near Main Street, Baxter Village and Kingsley Town Center, including ZIP codes 29707, 29708, 29715 in York County, SC.
Our technicians are in Fort Mill most days of the week, so a call from a business on Kingsley Town Center usually fits into the same day's route. Summer heat in the Charlotte region pushes condensers and compressors to their limit; for Fort Mill kitchens we check airflow, coil condition and electrical parts on every visit. When a part is not on the truck, we order it the same day from Charlotte-area suppliers and come back to Baxter Village as soon as it arrives. Because we also work in Tega Cay and Indian Land, a technician is often already nearby when a Fort Mill business calls.
Hobart problems we fix in Fort Mill
- Hobart commercial dishwasher: rinse not hot enough (below 180°f on hot-water units)
- Hobart commercial dishwasher: wash arm not spinning
- Hobart mixer, slicer and food prep: slicer blade dull or wobbly
- Hobart mixer, slicer and food prep: mixer won't start
Hobart equipment we repair
Save $50 on your repair
Book online or mention our website when you call and we take $50 off the repair. The service call is a flat $135, and you get a clear price before any work begins — no surprises.
Typical jobs we handle
Examples of common repairs on commercial refrigeration and kitchen equipment.
- Commercial DishwasherHotels & Banquet Facilities
Dish machine final rinse at 160°F
- What we found
- Booster heater element burned out
- What we did
- Replaced the element, verified 180°F final rinse
✓ Typically fixed in one visit
- Commercial DishwasherRestaurants
Dishwasher not draining
- What we found
- Drain valve stuck with debris
- What we did
- Cleared and rebuilt the drain valve
✓ Typically fixed in one visit
- Mixer, Slicer & Food PrepBakeries
Planetary mixer grinding in second speed
- What we found
- Worn transmission gear
- What we did
- Replaced the gear and lubricated the gearbox
✓ Usually needs a part ordered — two visits
- Commercial Range & CooktopRestaurants
Range pilots keep going out
- What we found
- Worn thermocouples on two burners
- What we did
- Replaced thermocouples, cleaned pilot assemblies
✓ Typically fixed in one visit
- Draft Beer & Keg CoolerBreweries & Taprooms
Foamy pours on every tap
- What we found
- Glycol chiller pump failing, lines warming
- What we did
- Replaced the glycol pump and topped up glycol
✓ Typically fixed in one visit
- Walk-In CoolerBreweries & Taprooms
Keg walk-in short-cycling on hot afternoons
- What we found
- Failed run capacitor and pitted contactor
- What we did
- Replaced capacitor and contactor, tested compressor under load
✓ Typically fixed in one visit
- Walk-In CoolerGrocery Stores & Supermarkets
Walk-in cooler slowly warming over several days
- What we found
- Condenser coil packed with dust and cottonwood; high head pressure
- What we did
- Deep-cleaned the condenser, checked charge and amperage
✓ Typically fixed in one visit
- Commercial OvenPizzerias
Conveyor pizza oven not reaching temperature
- What we found
- Failed igniter and flame sensor
- What we did
- Replaced igniter and sensor, verified bake temperature
✓ Typically fixed in one visit
Examples for illustration. Every job is diagnosed on site; parts, time and price depend on the equipment.
Our warranty
Labor warranty on every repair.
Parts warranty on every part we install.
Extended warranty available on select repairs and installations. The exact term is written on your estimate before work starts.
Frequently asked questions
Do you repair Hobart equipment in Fort Mill?
Yes. We repair Hobart commercial dishwasher, mixer, slicer and food prep for businesses throughout Fort Mill, SC.
Are you an authorized Hobart dealer?
No — we are an independent commercial service company. We repair Hobart equipment and warranty our work for 30 days labor and 90 days parts.
How much does Hobart repair cost in Fort Mill, SC?
The service call is a flat $135, which covers the trip and diagnosis. After diagnosis you get a written price for the repair before any work starts, and you save $50 on the repair when you book online or mention our website.
What are your hours in Fort Mill?
We are open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). Call (980) 983-2911 or send a request online and the first available operator will call you back.
Hours & contact
Commercial Appliances is open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). We serve Fort Mill, SC.
Phone: (980) 983-2911
Email: omnicommercialrefrigeration@gmail.com
Based in Charlotte, NC. We are a mobile service company — our technicians come to your business.
| Monday | 8:00 AM – 6:00 PM |
|---|---|
| Tuesday | 8:00 AM – 6:00 PM |
| Wednesday | 8:00 AM – 6:00 PM |
| Thursday | 8:00 AM – 6:00 PM |
| Friday | 8:00 AM – 6:00 PM |
| Saturday | 8:00 AM – 6:00 PM |
| Sunday | 10:00 AM – 3:00 PM |