Vulcan Repair in University City, Charlotte
University City businesses call us for fast, honest Vulcan repair.
- Licensed & insuredCommercial refrigeration and kitchen equipment technicians
- $135 service callClear price before any work starts
- $50 off your repairWhen you book online or mention the website
- Warranty on every job30-day labor, 90-day parts, extended 1, 3 or 5 years on select work
- Open 7 days a weekMon–Sat 8 AM–6 PM · Sun 10 AM–3 PM
- Same-day serviceWhen you call early — trucks stocked with common parts
You get a flat $135 service call and a written price before any work starts. Vulcan makes ranges, ovens, fryers, griddles and steamers, and we repair them on-site.
Vulcan service for University City businesses
University City's restaurants, hotels, campus dining and hospital kitchens serve tens of thousands of students and workers every day. We serve businesses near UNC Charlotte, J.W. Clay Boulevard and the Atrium Health University City campus, including ZIP codes 28262, 28213 in Mecklenburg County, NC.
We document every visit with the temperatures we measured and the parts we replaced, which helps University City managers with inspections and budgeting. Mecklenburg County health inspectors check cold-holding at 41°F or below and hot-holding at 135°F or above — we repair your Vulcan to hold those numbers. Summer heat in the Charlotte region pushes condensers and compressors to their limit; for University City kitchens we check airflow, coil condition and electrical parts on every visit. When a part is not on the truck, we order it the same day from Charlotte-area suppliers and come back to J.W. Clay Boulevard as soon as it arrives.
Vulcan problems we fix in University City
- Vulcan commercial oven: door won't close or seal
- Vulcan commercial oven: uneven baking or hot spots
- Vulcan commercial range and cooktop: knobs or valves stuck
- Vulcan commercial range and cooktop: oven below the range not heating
- Vulcan commercial fryer: pilot goes out
- Vulcan commercial fryer: oil overheating or not reaching set point
- Vulcan griddle and charbroiler: temperature not matching the dial
- Vulcan griddle and charbroiler: cold spots on the griddle
- Vulcan steamer, kettle and braising pan: scale build-up
- Vulcan steamer, kettle and braising pan: no steam or slow cooking
Save $50 on your repair
Book online or mention our website when you call and we take $50 off the repair. The service call is a flat $135, and you get a clear price before any work begins — no surprises.
Typical jobs we handle
Examples of common repairs on commercial refrigeration and kitchen equipment.
- Commercial OvenBakeries
Convection oven baking unevenly
- What we found
- Blower motor bearings worn
- What we did
- Replaced the convection blower motor
✓ Typically fixed in one visit
- Griddle & CharbroilerFood Trucks
Griddle has a cold spot on one side
- What we found
- Clogged burner ports
- What we did
- Cleaned and adjusted the burner, checked the thermostat
✓ Typically fixed in one visit
- Steamer, Kettle & Braising PanSchools & Universities
Steamer showing low-water alarm
- What we found
- Scaled water level probe
- What we did
- Cleaned the probe and delimed the generator
✓ Typically fixed in one visit
- Commercial FryerRestaurants
Fryer won't heat before lunch
- What we found
- Weak thermopile
- What we did
- Replaced the thermopile and tested the gas valve
✓ Typically fixed in one visit
- Commercial Range & CooktopRestaurants
Range pilots keep going out
- What we found
- Worn thermocouples on two burners
- What we did
- Replaced thermocouples, cleaned pilot assemblies
✓ Typically fixed in one visit
- Commercial FryerConvenience Stores & Gas Stations
Fryer overheating and tripping the high-limit
- What we found
- Temperature probe failing
- What we did
- Replaced the probe and calibrated the controller
✓ Typically fixed in one visit
- Commercial OvenPizzerias
Conveyor pizza oven not reaching temperature
- What we found
- Failed igniter and flame sensor
- What we did
- Replaced igniter and sensor, verified bake temperature
✓ Typically fixed in one visit
- Bar Cooler & Back BarBars & Nightclubs
Back-bar cooler bottles not cold
- What we found
- Thermostat out of calibration
- What we did
- Replaced the thermostat and set to 36°F
✓ Typically fixed in one visit
Examples for illustration. Every job is diagnosed on site; parts, time and price depend on the equipment.
Vulcan repair nearby
Other brands in University City
Our warranty
Labor warranty on every repair.
Parts warranty on every part we install.
Extended warranty available on select repairs and installations. The exact term is written on your estimate before work starts.
Frequently asked questions
Do you repair Vulcan equipment in University City?
Yes. We repair Vulcan commercial oven, commercial range and cooktop, commercial fryer, griddle and charbroiler, steamer, kettle and braising pan for businesses throughout University City, Charlotte.
Are you an authorized Vulcan dealer?
No — we are an independent commercial service company. We repair Vulcan equipment and warranty our work for 30 days labor and 90 days parts.
How much does Vulcan repair cost in University City, Charlotte?
The service call is a flat $135, which covers the trip and diagnosis. After diagnosis you get a written price for the repair before any work starts, and you save $50 on the repair when you book online or mention our website.
What are your hours in University City?
We are open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). Call (980) 983-2911 or send a request online and the first available operator will call you back.
Hours & contact
Commercial Appliances is open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). We serve University City, Charlotte.
Phone: (980) 983-2911
Email: omnicommercialrefrigeration@gmail.com
Based in Charlotte, NC. We are a mobile service company — our technicians come to your business.
| Monday | 8:00 AM – 6:00 PM |
|---|---|
| Tuesday | 8:00 AM – 6:00 PM |
| Wednesday | 8:00 AM – 6:00 PM |
| Thursday | 8:00 AM – 6:00 PM |
| Friday | 8:00 AM – 6:00 PM |
| Saturday | 8:00 AM – 6:00 PM |
| Sunday | 10:00 AM – 3:00 PM |