Fryer Pilot Keeps Going Out — Repair in Monroe, NC
Fryer Pilot Keeps Going Out in Monroe, NC? Monroe businesses call us for fast, honest commercial fryer repair. You get a flat $135 service call and a written price before any work starts.
- Licensed & insuredCommercial refrigeration and kitchen equipment technicians
- $135 service callClear price before any work starts
- $50 off your repairWhen you book online or mention the website
- Warranty on every job30-day labor, 90-day parts, extended 1, 3 or 5 years on select work
- Open 7 days a weekMon–Sat 8 AM–6 PM · Sun 10 AM–3 PM
- Same-day serviceWhen you call early — trucks stocked with common parts
Likely causes
- Drafts from hood
- Gas valve failure
- Weak thermopile or thermocouple
- Dirty pilot orifice
What to do before we arrive
- Relight per the label
- Check for strong drafts
- Don't keep relighting if it won't hold
Local service
We serve businesses near downtown Monroe on Main Street, Roosevelt Boulevard (US-74) and the Charlotte–Monroe Executive Airport area, including ZIP codes 28110, 28112 in Union County, NC.
When a part is not on the truck, we order it the same day from Charlotte-area suppliers and come back to Roosevelt Boulevard (US-74) as soon as it arrives. Because we also work in Indian Trail and Wesley Chapel, a technician is often already nearby when a Monroe business calls. Union County health inspectors check cold-holding at 41°F or below and hot-holding at 135°F or above — we repair your commercial fryer to hold those numbers. Businesses in ZIP 28110 and 28112 can book online in 30 seconds, and the first available operator calls back during business hours.
Save $50 on your repair
Book online or mention our website when you call and we take $50 off the repair. The service call is a flat $135, and you get a clear price before any work begins — no surprises.
Typical jobs we handle
Examples of common repairs on commercial refrigeration and kitchen equipment.
- Commercial FryerConvenience Stores & Gas Stations
Fryer overheating and tripping the high-limit
- What we found
- Temperature probe failing
- What we did
- Replaced the probe and calibrated the controller
✓ Typically fixed in one visit
- Commercial FryerRestaurants
Fryer won't heat before lunch
- What we found
- Weak thermopile
- What we did
- Replaced the thermopile and tested the gas valve
✓ Typically fixed in one visit
- Walk-In CoolerBreweries & Taprooms
Keg walk-in short-cycling on hot afternoons
- What we found
- Failed run capacitor and pitted contactor
- What we did
- Replaced capacitor and contactor, tested compressor under load
✓ Typically fixed in one visit
- Refrigerated Display CaseBakeries
Bakery display case warm at the front
- What we found
- Evaporator iced from a bad defrost timer
- What we did
- Replaced the timer, defrosted, verified temperatures
✓ Typically fixed in one visit
- Walk-In FreezerSchools & Universities
Ice building up on the freezer floor near the door
- What we found
- Torn door gasket and failed door-frame heater
- What we did
- Replaced the gasket and frame heater wire
✓ Typically fixed in one visit
- Bar Cooler & Back BarBars & Nightclubs
Back-bar cooler bottles not cold
- What we found
- Thermostat out of calibration
- What we did
- Replaced the thermostat and set to 36°F
✓ Typically fixed in one visit
- Draft Beer & Keg CoolerBreweries & Taprooms
Foamy pours on every tap
- What we found
- Glycol chiller pump failing, lines warming
- What we did
- Replaced the glycol pump and topped up glycol
✓ Typically fixed in one visit
- Commercial DishwasherRestaurants
Dishwasher not draining
- What we found
- Drain valve stuck with debris
- What we did
- Cleared and rebuilt the drain valve
✓ Typically fixed in one visit
Examples for illustration. Every job is diagnosed on site; parts, time and price depend on the equipment.
Frequently asked questions
Why is my fryer pilot keeps going out?
Most often: weak thermopile or thermocouple; dirty pilot orifice; drafts from hood; gas valve failure.
How much does commercial fryer repair cost in Monroe, NC?
The service call is a flat $135, which covers the trip and diagnosis. After diagnosis you get a written price for the repair before any work starts, and you save $50 on the repair when you book online or mention our website.
What are your hours in Monroe?
We are open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). Call (980) 983-2911 or send a request online and the first available operator will call you back.
Do you serve ZIP code 28110?
Yes. We serve Monroe and all of Monroe, NC, including ZIP codes 28110, 28112.
Hours & contact
Commercial Appliances is open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). We serve Monroe, NC.
Phone: (980) 983-2911
Email: omnicommercialrefrigeration@gmail.com
Based in Charlotte, NC. We are a mobile service company — our technicians come to your business.
| Monday | 8:00 AM – 6:00 PM |
|---|---|
| Tuesday | 8:00 AM – 6:00 PM |
| Wednesday | 8:00 AM – 6:00 PM |
| Thursday | 8:00 AM – 6:00 PM |
| Friday | 8:00 AM – 6:00 PM |
| Saturday | 8:00 AM – 6:00 PM |
| Sunday | 10:00 AM – 3:00 PM |