Steamer Not Producing Steam — Repair in Matthews, NC
Steamer Not Producing Steam in Matthews, NC? Our steamer, kettle and braising pan repair service covers all of Matthews, NC.
- Licensed & insuredCommercial refrigeration and kitchen equipment technicians
- $135 service callClear price before any work starts
- $50 off your repairWhen you book online or mention the website
- Warranty on every job30-day labor, 90-day parts, extended 1, 3 or 5 years on select work
- Open 7 days a weekMon–Sat 8 AM–6 PM · Sun 10 AM–3 PM
- Same-day serviceWhen you call early — trucks stocked with common parts
We know the local businesses, the building types and how hot a Matthews kitchen gets in July.
Likely causes
- Water supply problem
- Element or burner failure
- Failed water level probe
- Scale build-up
What to do before we arrive
- Check the water supply
- Check for low-water alarm
- Run a delime cycle if due
Local service
We serve businesses near downtown Matthews on Trade Street, Independence Boulevard (US-74) and Sycamore Commons, including ZIP codes 28104, 28105 in Mecklenburg County, NC.
From quick-service counters near Sycamore Commons to full kitchens near downtown Matthews on Trade Street, Matthews businesses rely on us for steamer, kettle and braising pan work. Our technicians are in Matthews most days of the week, so a call from a business on Sycamore Commons usually fits into the same day's route. When a part is not on the truck, we order it the same day from Charlotte-area suppliers and come back to Independence Boulevard (US-74) as soon as it arrives. Summer heat in the Charlotte region pushes condensers and compressors to their limit; for Matthews kitchens we check airflow, coil condition and electrical parts on every visit.
Save $50 on your repair
Book online or mention our website when you call and we take $50 off the repair. The service call is a flat $135, and you get a clear price before any work begins — no surprises.
Typical jobs we handle
Examples of common repairs on commercial refrigeration and kitchen equipment.
- Steamer, Kettle & Braising PanSchools & Universities
Steamer showing low-water alarm
- What we found
- Scaled water level probe
- What we did
- Cleaned the probe and delimed the generator
✓ Typically fixed in one visit
- Walk-In CoolerBreweries & Taprooms
Keg walk-in short-cycling on hot afternoons
- What we found
- Failed run capacitor and pitted contactor
- What we did
- Replaced capacitor and contactor, tested compressor under load
✓ Typically fixed in one visit
- Walk-In CoolerGrocery Stores & Supermarkets
Walk-in cooler slowly warming over several days
- What we found
- Condenser coil packed with dust and cottonwood; high head pressure
- What we did
- Deep-cleaned the condenser, checked charge and amperage
✓ Typically fixed in one visit
- Undercounter & Worktop RefrigeratorRestaurants
Chef base losing temperature during the rush
- What we found
- Front grille and condenser clogged with grease
- What we did
- Cleaned the condenser, replaced a worn drawer gasket
✓ Typically fixed in one visit
- Commercial DishwasherHotels & Banquet Facilities
Dish machine final rinse at 160°F
- What we found
- Booster heater element burned out
- What we did
- Replaced the element, verified 180°F final rinse
✓ Typically fixed in one visit
- Commercial DishwasherRestaurants
Dishwasher not draining
- What we found
- Drain valve stuck with debris
- What we did
- Cleared and rebuilt the drain valve
✓ Typically fixed in one visit
- Commercial OvenPizzerias
Conveyor pizza oven not reaching temperature
- What we found
- Failed igniter and flame sensor
- What we did
- Replaced igniter and sensor, verified bake temperature
✓ Typically fixed in one visit
- Ice MachineHotels & Banquet Facilities
Floor ice machine not harvesting
- What we found
- Faulty harvest assist and a weak water pump
- What we did
- Replaced both parts and ran test cycles
✓ Typically fixed in one visit
Examples for illustration. Every job is diagnosed on site; parts, time and price depend on the equipment.
Frequently asked questions
Why is my steamer not working?
Most often: scale build-up; failed water level probe; element or burner failure; water supply problem.
How much does steamer, kettle and braising pan repair cost in Matthews, NC?
The service call is a flat $135, which covers the trip and diagnosis. After diagnosis you get a written price for the repair before any work starts, and you save $50 on the repair when you book online or mention our website.
What are your hours in Matthews?
We are open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). Call (980) 983-2911 or send a request online and the first available operator will call you back.
Do you serve ZIP code 28104?
Yes. We serve Matthews and all of Matthews, NC, including ZIP codes 28104, 28105.
Hours & contact
Commercial Appliances is open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). We serve Matthews, NC.
Phone: (980) 983-2911
Email: omnicommercialrefrigeration@gmail.com
Based in Charlotte, NC. We are a mobile service company — our technicians come to your business.
| Monday | 8:00 AM – 6:00 PM |
|---|---|
| Tuesday | 8:00 AM – 6:00 PM |
| Wednesday | 8:00 AM – 6:00 PM |
| Thursday | 8:00 AM – 6:00 PM |
| Friday | 8:00 AM – 6:00 PM |
| Saturday | 8:00 AM – 6:00 PM |
| Sunday | 10:00 AM – 3:00 PM |