Prep Table Not Keeping Food Cold — Repair in Fort Mill, SC
Prep Table Not Keeping Food Cold in Fort Mill, SC? Our prep table and sandwich unit repair service covers all of Fort Mill, SC.
- Licensed & insuredCommercial refrigeration and kitchen equipment technicians
- $135 service callClear price before any work starts
- $50 off your repairWhen you book online or mention the website
- Warranty on every job30-day labor, 90-day parts, extended 1, 3 or 5 years on select work
- Open 7 days a weekMon–Sat 8 AM–6 PM · Sun 10 AM–3 PM
- Same-day serviceWhen you call early — trucks stocked with common parts
We know the local businesses, the building types and how hot a Fort Mill kitchen gets in July.
Likely causes
- Dirty condenser
- Bad thermostat
- Blocked rail air duct
- Weak evaporator fan
- Low refrigerant
What to do before we arrive
- Close the rail lid
- Move pans to the cabinet or walk-in
- Clean the condenser grille
Local service
We serve businesses near Main Street, Baxter Village and Kingsley Town Center, including ZIP codes 29707, 29708, 29715 in York County, SC.
York County health inspectors check cold-holding at 41°F or below and hot-holding at 135°F or above — we repair your prep table and sandwich unit to hold those numbers. Our technicians are in Fort Mill most days of the week, so a call from a business on Kingsley Town Center usually fits into the same day's route. Because we also work in Tega Cay and Indian Land, a technician is often already nearby when a Fort Mill business calls. Summer heat in the Charlotte region pushes condensers and compressors to their limit; for Fort Mill kitchens we check airflow, coil condition and electrical parts on every visit.
Save $50 on your repair
Book online or mention our website when you call and we take $50 off the repair. The service call is a flat $135, and you get a clear price before any work begins — no surprises.
Typical jobs we handle
Examples of common repairs on commercial refrigeration and kitchen equipment.
- Prep Table & Sandwich UnitPizzerias
Pizza prep table rail pans at 46°F
- What we found
- Dirty condenser and weak evaporator fan
- What we did
- Cleaned the condenser, replaced the fan motor, rail back to 39°F
✓ Typically fixed in one visit
- Prep Table & Sandwich UnitRestaurants
Sandwich unit lid won't stay open
- What we found
- Broken lid hinge pin
- What we did
- Replaced the hinge set and adjusted the lid
✓ Typically fixed the same day
- Steamer, Kettle & Braising PanSchools & Universities
Steamer showing low-water alarm
- What we found
- Scaled water level probe
- What we did
- Cleaned the probe and delimed the generator
✓ Typically fixed in one visit
- Ice MachineBars & Nightclubs
Ice machine making half the usual ice
- What we found
- Heavy scale on the evaporator plate
- What we did
- Descaled, sanitized and replaced the water filter
✓ Typically fixed in one visit
- Mixer, Slicer & Food PrepBakeries
Planetary mixer grinding in second speed
- What we found
- Worn transmission gear
- What we did
- Replaced the gear and lubricated the gearbox
✓ Usually needs a part ordered — two visits
- Walk-In FreezerSchools & Universities
Ice building up on the freezer floor near the door
- What we found
- Torn door gasket and failed door-frame heater
- What we did
- Replaced the gasket and frame heater wire
✓ Typically fixed in one visit
- Condensing Unit & CompressorGrocery Stores & Supermarkets
Rooftop condensing unit tripping the breaker
- What we found
- Shorted condenser fan motor
- What we did
- Replaced the fan motor and checked electrical connections
✓ Typically fixed in one visit
- Reach-In RefrigeratorCafés & Coffee Shops
Dairy reach-in warm at the top shelf
- What we found
- Evaporator fan blade cracked, poor airflow
- What we did
- Replaced fan blade and motor, rebalanced airflow
✓ Typically fixed in one visit
Examples for illustration. Every job is diagnosed on site; parts, time and price depend on the equipment.
Frequently asked questions
Why is my prep table not cold?
Most often: dirty condenser; weak evaporator fan; blocked rail air duct; low refrigerant.
How much does prep table and sandwich unit repair cost in Fort Mill, SC?
The service call is a flat $135, which covers the trip and diagnosis. After diagnosis you get a written price for the repair before any work starts, and you save $50 on the repair when you book online or mention our website.
What are your hours in Fort Mill?
We are open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). Call (980) 983-2911 or send a request online and the first available operator will call you back.
Do you serve ZIP code 29707?
Yes. We serve Fort Mill and all of Fort Mill, SC, including ZIP codes 29707, 29708, 29715.
Hours & contact
Commercial Appliances is open Monday through Saturday from 8:00 AM to 6:00 PM, and Sunday from 10:00 AM to 3:00 PM (Eastern Time). We serve Fort Mill, SC.
Phone: (980) 983-2911
Email: omnicommercialrefrigeration@gmail.com
Based in Charlotte, NC. We are a mobile service company — our technicians come to your business.
| Monday | 8:00 AM – 6:00 PM |
|---|---|
| Tuesday | 8:00 AM – 6:00 PM |
| Wednesday | 8:00 AM – 6:00 PM |
| Thursday | 8:00 AM – 6:00 PM |
| Friday | 8:00 AM – 6:00 PM |
| Saturday | 8:00 AM – 6:00 PM |
| Sunday | 10:00 AM – 3:00 PM |