Avantco Prep Table & Sandwich Unit Repair in Charlotte, NC
Need a Avantco prep table and sandwich unit repaired? Warm rail pans are the classic complaint.
- Licensed & insuredCommercial refrigeration and kitchen equipment technicians
- $135 service callClear price before any work starts
- $50 off your repairWhen you book online or mention the website
- Warranty on every job30-day labor, 90-day parts, extended 1, 3 or 5 years on select work
- Open 7 days a weekMon–Sat 8 AM–6 PM · Sun 10 AM–3 PM
- Same-day serviceWhen you call early — trucks stocked with common parts
The causes are usually a dirty condenser, a weak evaporator fan, a blocked air duct to the rail, low refrigerant or a failed thermostat. Our technicians service Avantco prep table and sandwich unit units across Charlotte and nearby cities.
Common Avantco prep table and sandwich unit problems
- Top rail pans above 41°F
- Cabinet cold but rail warm
- Ice on the coil
- Lid hinge broken or lid not closing
- Water leaking into the cabinet
- Compressor overheating
What we repair on Avantco prep table and sandwich unit units
- Rail airflow and duct repair
- Fan motor replacement
- Condenser cleaning
- Thermostat and controller replacement
- Leak repair and recharge
- Lid hinge and gasket replacement
Technician tip
Close the rail lid during slow periods — it cuts compressor run time and keeps pans at a safe temperature.
Save $50 on your repair
Book online or mention our website when you call and we take $50 off the repair. The service call is a flat $135, and you get a clear price before any work begins — no surprises.
Typical jobs we handle
Examples of common repairs on commercial refrigeration and kitchen equipment.
- Prep Table & Sandwich UnitRestaurants
Sandwich unit lid won't stay open
- What we found
- Broken lid hinge pin
- What we did
- Replaced the hinge set and adjusted the lid
✓ Typically fixed the same day
- Prep Table & Sandwich UnitPizzerias
Pizza prep table rail pans at 46°F
- What we found
- Dirty condenser and weak evaporator fan
- What we did
- Cleaned the condenser, replaced the fan motor, rail back to 39°F
✓ Typically fixed in one visit
- Commercial FryerConvenience Stores & Gas Stations
Fryer overheating and tripping the high-limit
- What we found
- Temperature probe failing
- What we did
- Replaced the probe and calibrated the controller
✓ Typically fixed in one visit
- Ice MachineBars & Nightclubs
Ice machine making half the usual ice
- What we found
- Heavy scale on the evaporator plate
- What we did
- Descaled, sanitized and replaced the water filter
✓ Typically fixed in one visit
- Ice MachineConvenience Stores & Gas Stations
Ice machine showing a flashing error light
- What we found
- Water inlet valve not opening
- What we did
- Replaced the inlet valve and verified full fill
✓ Typically fixed in one visit
- Walk-In CoolerRestaurants
Walk-in cooler at 48°F before dinner service
- What we found
- Evaporator fan motor seized; coil starting to ice
- What we did
- Replaced the fan motor, cleared the coil, verified 36°F box temperature
✓ Typically fixed in one visit
- Reach-In FreezerPizzerias
Reach-in freezer frosting up every few days
- What we found
- Defrost heater open circuit
- What we did
- Replaced the defrost heater and tested a full defrost cycle
✓ Typically fixed in one visit
- Steamer, Kettle & Braising PanSchools & Universities
Steamer showing low-water alarm
- What we found
- Scaled water level probe
- What we did
- Cleaned the probe and delimed the generator
✓ Typically fixed in one visit
Examples for illustration. Every job is diagnosed on site; parts, time and price depend on the equipment.
Other prep table and sandwich unit brands we repair
Our warranty
Labor warranty on every repair.
Parts warranty on every part we install.
Extended warranty available on select repairs and installations. The exact term is written on your estimate before work starts.
Frequently asked questions
Why is my Avantco prep table and sandwich unit not working?
The most common causes are: top rail pans above 41°f; cabinet cold but rail warm; ice on the coil. A technician confirms the cause on site before quoting the repair.
Why are my prep table pans warm but the cabinet is cold?
The rail depends on airflow from the evaporator. A weak fan, iced coil or blocked duct starves the pans first.
How much is Avantco prep table and sandwich unit repair?
$135 service call with diagnosis, then a written price. $50 off the repair when booked online.